Recently, Xiagong Chusheng Special Purpose Vehicle Co., Ltd. has become increasingly popular in the production of mobile refuelling vehicles. Many users are the first time to contact the fuel tanker special equipment such as computer tax-controlled mobile fuel dispensers. Therefore, some considerations in the use of fuel dispensers are not Know well:
1. How to operate the computer-controlled tax refueling machine for mobile refueling vehicles: When the refueling vehicle refuels, raise the fuel gun and send a signal to the computer device. The computer device sends a start signal, starts the motor, opens the solenoid valve, and displays the original panel. The data is cleared. After the motor drives the oil pump to pressurize, it is sent to the oil separator to separate the oil and gas. The gas is discharged into the atmosphere. The pressure oil enters the measuring transducer and is injected into the oil receiving container through the electromagnetic valve, the conductive rubber hose and the oil gun. At the same time, after the pressure oil is measured by the measuring transducer, the mechanical motion is replaced by the sensor with an electric pulse signal. If it is preset refueling, input the preset number from the keyboard first, and then raise the gun and add fuel. When the added quantity reaches the preset value, close the solenoid valve and the motor and stop the refueling.
2. When supplying power to the fuel dispenser, ensure that the voltage is within the range of DC10V~DC30V so as not to burn the computer components by the peak voltage.
3, because the pump to the tanker is provided by the car, in order to ensure stable pressure, the car pipeline should be equipped with an overflow valve, if not, should be specified in the order, requiring the tanker with a relief valve to avoid damage Tanker.
4. When using the oil gun (oil dispenser automatic return reel), avoid using the oil gun's oil filling pipe to knock on the oil receiving container, press the switch and other incorrect operation, this operation may damage the root of the oil filling pipe and cause oil leakage. To check regularly, tighten the stop screw on the fill tube to prevent loosening or damage to the root of the fill tube.
5, the tank should be regularly cleaned to keep the oil clean.
6. The metering verification of fuel dispensers shall be conducted in accordance with the relevant provisions of JJG443-2006 "Measurement Regulations for Measurement of Fuel Refueler".
7. The filter is installed in front of the oil inlet of the tanker. Since the conditions of the oil products are not the same everywhere, the replacement cycle of the filter cannot be clearly defined; when the flow of the tanker suddenly decreases, replace the filter; if after the replacement, replace the filter; The traffic is still abnormal. Check whether other components affect the traffic. If the traffic is affected, replace the traffic.
Xiagong Chusheng Special Purpose Vehicle Co., Ltd. Refueling vehicle users should be familiar with the use of fire extinguishers and inspect and maintain them in accordance with their instructions.
When you need to consult or repair, please contact our factory after-sales service department, and safekeeping of the purchase certificate to confirm the car is in the warranty period. Chassis car after-sales service by the chassis manufacturer responsible for the car; the factory only for the special modification of the vehicle part of the "three guarantees" in the use of the process, whenever and where there is a fault or problem, please call, email us, we Will be given promptly to handle and give a clear reply within 24 hours after receiving the information. Tel 18727982299 (Manager Wang)
It can slow down the reaction, maintain chemical balance, reduce surface tension, prevent light, thermal decomposition or oxidative decomposition. it mainly includes lead salts, metal soaps, organic tin, organic antimony, organic rare earths, pure organic compounds. Thermal stabilizers commonly used in industry mainly include lead salts, metal soaps, organic tin, organic antimony, organic rare earths, pure organic compounds, etc.
1.1 Organotin
(1) Excellent transparency The biggest advantage of organotin stabilizers is that they have excellent transparency. The use of organotin stabilizers in PVC formulations can produce crystalline products. Because of this, organic tin can be used in bottles, containers, corrugated boards, various types of rigid packaging containers, hoses, profiles, films, etc.
(2) Extraordinary thermal stability In terms of thermal stability, there is no other type of thermal stabilizer that can surpass it. Therefore, it is the preferred stabilizer for rigid PVC, and some varieties have better performance in soft products. Suitable for all PVC homopolymers, such as emulsion, suspension and bulk PVC, as well as vinyl chloride copolymers, graft polymers and polymer blends.
(3) The product is non-toxic. Most organotin stabilizers are non-toxic, and the migration of organotin stabilizers in rigid PVC is minimal. Therefore, organotin stabilizers are the preferred heat stabilizers for PVC for food contact.
(4) Good compatibility. Organotin stabilizers have good compatibility with PVC, so there is generally no precipitation on the metal surface, such as lead salt stabilizers and metal soap stabilizer systems.
(5) Poor lubricity Sulfur-containing tin stabilizers have poor self-lubricity. Therefore, many commercially available sulfur-containing organotins are equipped with lubricants to prevent hot melt from adhering to processing equipment during processing.
(6) High cost Compared with other types of stabilizers, the overall performance of organotin stabilizers is closer to the ideal stabilizer. However, all organotin stabilizers, regardless of their structure, have the main disadvantage that their manufacturing cost is much higher than that of lead stabilizers or metal soap compounds. In recent years, by adopting new synthetic technology, or reducing its usage in formulas, its formula cost has been reduced. In the 1970s, foreign countries developed low-priced tin products, which reduced the tin content, which also reduced the price to a certain extent.
1.2 Lead salt
(1) l Excellent stability experiments proved that among the commonly used basic lead salts, the heat resistance of sulfite is better than that of sulfate, and the heat resistance of sulfate is better than that of phosphite. The tribasic lead sulfate, which is widely used in the PVC industry, has a higher effective lead content and shows better thermal stability than other products.
(2) Excellent insulation. Because lead salt is non-ionic and non-conductive, it is inert, which makes lead salt stabilizers widely used in wire and cable industries.
(3) Excellent weather resistance. Many salt compounds can act as white pigments and can show strong covering power, so they have strong weather resistance.
(4) Poor transparency Transparency is a problem related to weather resistance. When used in wires, cables and record materials, there is no need to care about transparency, because most of these products are white or very dark black.
(5) Inexpensive lead salt stabilizer is the lowest price among all stabilizers. Therefore, despite the continuous introduction of new stabilizers, lead salt stabilizers still dominate the stabilizer market after half a century. The composite lead salt introduced to solve the dust and dispersion problem has increased in price, but still maintains a competitive advantage with other types of stabilizers.
(6) The toxicity of the toxic lead salt stabilizer limits its application in many occasions with strict hygiene requirements. For example, many countries have revised the lead content standards in drinking water, and it is no longer possible to use lead salt in PVC water pipes.
(7) Poor dispersibility The dispersibility of salt lead is poor, but the newly launched one-package product is equipped with lubricants, which solves the dispersibility problem to a certain extent. Because of the above characteristics of lead salt stabilizers, they are especially suitable for high-temperature processing. They are widely used in various opaque hard and soft products and cable materials, such as various pipes, plates, indoor and outdoor profiles, foam plastics, artificial leather, and wires. Cables, records, welding rods, etc. The most important lead salt stabilizers are tribasic lead sulfate, dibasic lead phosphite, and dibasic lead stearate.
1.3 Organic antimony
(1) Better stability. The organic antimony stabilizer has basically the same color stability and lower melt viscosity as organotin at the same temperature. In the twin-screw extrusion process, the effect is particularly outstanding when used in combination with calcium stearate. .
(2) The price of organic antimony stabilizer is much lower than that of methyl tin or butyl tin. In addition, the amount of organic antimony used is relatively low, so the use of organic antimony can achieve a better performance/price balance.
(3) The product is non-toxic. In the United States, when a twin-screw extruder is used to manufacture PVC pipes, the PVC water supply pipe manufactured with a formula composed of antimony stabilizers, calcium stearate and other lubricants conforms to the U.S. NSF (National Sanitation Foundation) )Regulation.
(4) Poor transparency and light stability. The transparency of organic antimony compounds is not as good as organotin stabilizers, and it is also lower than the barium/fu and calcium/zinc metal soap system. It is close to lead salts and has poor light stability, so antimony is stable. The agent is mostly used for indoor products without color requirements. The antimony stabilizer itself is also required to be stored in an opaque container.
(5) Poor lubricity. Antimony stabilizers have poor lubricity. Therefore, its use must be combined with a large amount of lubricant without exception.
1.4 Metal soap
(1) The tin soap stabilizer Fu soap is the best type of metal soap. Its advantages are also reflected in the absence of initial coloring, and can produce colorless and transparent products; excellent light stability; it has the effect of preventing precipitation and adhesion. . However, because tin salt is toxic, there are strict regulations on its manufacture and use in the Labor Safety and Health Law. In recent years, the use of Fuzao has shown a downward trend.
(2) Zinc soap stabilizerThe thermal stability of zinc-based stabilizer to PVC is extremely poor. The sample with zinc soap suddenly turns black when heated, that is, the so-called "Zine burning" phenomenon occurs, but it has the following advantages: The initial coloring is excellent; the effect of preventing fouling is good; it can improve the weather resistance; many zinc soaps are recognized as non-toxic stabilizers, so they can be used in non-toxic formulations with calcium soaps.
(3) Barium soap stabilizer Barium compounds have good thermal stability and good lubricity, but the red initial coloration occurs during processing, and it is easy to cause sticking to the roller.
(4) The stability of calcium soap stabilizer is poor, but it is recognized as a non-toxic additive in the world and has excellent lubricity.
(5) Other metal soap stabilizers used in the industry include magnesium stearate, file stearate, aluminum stearate, potassium stearate, etc., among which magnesium stearate is similar to calcium stearate and can be used Materials that are in contact with food; aluminum stearate is similar to zinc stearate, and is approved by the U.S. FDA and the Japanese Vinyl Chloride Food Hygiene Association for food packaging; Stearic Acid files and potassium stearate are also non-toxic products and belong to lead salts , Tin soap and barium soap substitute.
(6) The performance requirements of the composite metal soap stabilizer processing industry for stabilizers are various, and a single metal soap often cannot meet the use requirements, so the use of composite stabilizers has become a trend. A single metal soap compound is rarely used in the PVC industry, and it is usually a compound of several metal soaps. This compound is not a simple addition of properties, but takes advantage of the synergy between the components. The composite metal soap stabilizer generally includes the stabilizer main body (i.e. metal soap), solvent (organic solvent, plasticizer, liquid non-metal stabilizer, etc.), functional additives (auxiliary stabilizer, transparency modifier, light stabilizer, Lubricants, etc.). According to the form, it is divided into solid compound and liquid compound. According to the main component, it can be divided into calcium/zinc compound stabilizer, barium/fu compound stabilizer, barium/zinc compound stabilizer, etc. Among them, the calcium/zinc composite stabilizer has a pivotal role in replacing toxic metals because it is non-toxic.
1.5 Rare earth stabilizer
(1) Excellent thermal stability The thermal stability of rare earth stabilizers is better than traditional lead salt series and barium/zinc, barium/ho/zinc stabilizers. In some applications, rare earth stabilizers can partially or completely replace organotin.
(2) Good transparency. The refractive index of rare earth stabilizers is very close to that of PVC Resin, which can replace traditional organotin and be used in the field of products with higher transparency requirements.
(3) Excellent weather resistance. Rare earth elements can absorb 230-320nm ultraviolet light. Therefore, rare earth stabilizers have anti-photoaging effects and are suitable for outdoor products such as PVC corrugated boards and window materials.
(4) Excellent electrical insulation properties. Some rare earth multifunctional stabilizers can be used to replace lead salt stabilizers in cable material formulations, and their electrical insulation properties are comparable to lead salts.
(5) Non-toxic, safe and hygienic. Rare earth elements are low-toxic elements and have no toxic hazards to the human body in their production, processing, transportation and storage. Rare earth stabilizers are non-toxic products and can be used in food packaging and medical packaging products.
(6) The processing performance is slightly worse. In the case of a large amount of rare earth stabilizer, the roll release of the material is not ideal, and there is a tendency to press out. Generally, better results can be achieved by using stearic acid or calcium stearate in combination.
In summary, rare earth stabilizers can be used for water pipes, injection pipe fittings, window frame profiles, door panels, wire ducts, foam products, artificial leather, cable materials, soft and hard transparent products, food packaging materials, etc.
1.6 Auxiliary stabilizers Auxiliary stabilizers include phosphite, epoxy soybean oil, hindered phenols, etc., which mainly rely on the synergistic effect between metal stabilizers to improve the stabilizing effect, and are generally called co-stabilizers. In addition to compounds such as mesaminocrotonic acid ester, 2-phenyl saccharin, vein derivatives, and diketone can be used in combination with metal stabilizers to improve the effect of metal stabilizers, they also have a certain stabilizing effect. Such compounds are usually called pure organic stabilizers. With the development of PVC stabilizers today, the progress of metal stabilizers is relatively slow, and the research and development of auxiliary stabilizers are unprecedentedly active, which has constituted a major trend in the field of PvC stabilizers. Auxiliary stabilizers are rarely used alone, and are often used in conjunction with primary stabilizers to improve initial coloration or improve long-term stability.
Lead Salt Stabilizer, Compound Stabilizer,Pvc Stabilizer,Titanium Dioxide Anatase
Henan Shunbang Chemical Industry CO.,Ltd , https://www.sbpolymer.com